Aspire Tigon Kit User Manual/Instructions PDF | Download - Only take news things-Onlytakenew.com

How to use Aspire Tigon Kit

Read this information leaflet fully before you start using this product as it contains important information. The notes below relate to when the device is filled with e-liquid that contains nicotine.

Aspire Tigon is intended for adult smokers. This product is not recommended for non-smokers, young people under the age of 18 years, pregnant or breast feeding women and those experiencing general ill health.

Tigon Kit Contents:

1* Tigon Kit 1* Glass tube 2* Ni80 Coils (1*1.2Ω & 1*0.4Ω preinstalled) 10* O-rings 1* Extra drip tip 1* USB cable 1* User manual 1* Warranty card

Tigon Tank Features Super easy top fill Child resistant 3.5ml capacity Bottom adjustable airflow E-liquid sealing mechanism Coil resistance: 1.2Ω(10-12W) & 0.4Ω(23-28W) Great vapor and flavor production Super efficient wicking Suitable for both MTL hits and restricted lung hits Diameter: 23mm Length (including drip tip): 63mm

Tank Filling 1. Pull the top cap up, place your thumb on the top cap right on the drop symbol. 2. Push the top cap away until the filling hole is revealed. 3. Add your preferred e-liquid into the tank through the filling hole. 4. Slide the top cap back into place. 5. Press the top cap down firmly to seal.

Coil Installation 1. Unscrew to remove the base hardware. 2. Pull to remove the used coil. 3. Put a new coil into the chamber. 4. Screw the base hardware back onto the tank. NB: Coil can be replaced even when the tank is full

Glass Tube Replacement
1. Unscrew to remove the top hardware.
2. Remove the used glass tube.
3. Attach a new glass tube.
4. Screw the top hardware into place.

Mod Specifications
Output wattage: Bypass Output voltage: 3.3-4.2V
Continuous firing time: 10 seconds
Battery Type: Built-in
Battery capacity:2600mAh
Diameter:23mm
Length: 94mm

Tigon Starter Kit Instructions

• Press the fire button 5 times within 2 seconds to either lock or unlock the device. The LED light will flash pink 3 times at the same time.
• When the device is on press the fire button, the LED light will indicate your device's current charge. When its current charge capacity is above 3.8 volts the indicator light will be pink. When the charge is between 3.8 and 3.5 volts the light will be blue. When the charge drops below 3.5 volts the light will then become red to remind you that it is time to charge your device.

Aspire Tigon Protection Features

• Automatic Cutoff: The preset continuous fire time is 10 seconds, after 10 seconds of continuous firing, the device will stop firing and the LED light will flash 10 times, it will fire again when the button is pressed.
• Short Circuit Protection: When the device detects a short, it will stop firing, and the LED light will flash pink 3 times .
• Low Voltage Protection: When the battery level drops below 3.2V, the device will not function and the LED light will flash red 15 times.
• Overcharge Protection: When the device is fully charged, it will stop charging to prevent overcharging of your battery.
• Over heat protection: When the temperature of the control board is above 75℃/167℉, the LED light will remain on pink for 3 seconds to indicate an overheat and the device will cut off.

Aspire Tigon Kit Charging Instructions •

Charge via the Micro USB port. Maximum charge current can reach up to 2A.
• When the USB cable is attached or detached the device indicator light will flash pink 3 times. While charging the LED will indicate the device’s current charge status: 3.5 volts or less= red light; 3.5 to 3.8 volts= blue light; 3.8 volts and above= pink light. When the device is fully charged the LED will flash pink 20 times then remain off.